Roborooter.com

Hand crafted bits since Y2K

November 16, 2024

Making Some Shelves

#making #woodworking #3dprinting

A build log about a smaller project that took my mind off of everything.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

A very messy garage with a sheet of plywood in the back.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

A first draft workbench, four posts, an outside frame and a 3 sided frame near the bottom.

The underside of the workbench, lacking any supports for the plywood.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Side view with a transparent top for some reason.

You can clearly see some 2x4s attached to the inside of the 4x4s

A transparent top the workbench with the edges of the back crossbeams peaking out because trig is hard if you don't remember it.

You can kind of see the new 8 foot support beams

Front view, it's.. fine. Same thing, two cross beams going from the lower corners to the top center.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Yellow cross beams on the inside bumping up against the new interior support beams.

Ok so maybe I didn't quite figure out the math to keep my parts from overlapping. The yellow cross beams poking through the support beams from below.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

The plywood doesn't drop in anymore but it's fine, this is much more solid.

I also figured out how to keep the wood from overlapping at the top!

(underside view of the work bench showing an upper frame that completely supports the plywood.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

A thinner sleeker dual shelved solution!

So it's a wooden shelf, with a shelf at 4ft and another at 2ft. Four posts adorn each corner, and the lower shelf has 10in cutouts in it's corners to fit between the posts.

The underside shows 2x3x4 blocks up against the posts, and a single stretch of 2x3 between the shorter edge of the posts

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

A bottom view showing less support for the posts on the bottom frame.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Assembly guide with some design pictures and some info about the construction.

-4x4 legs
-The long sides of the frame go the entire width of the shelf
-The top shelf has 4” supports on the long side and 14” supports on
the short sides between the posts
- The bottom shelf has 5”x5” cutouts on each corner

A table of cut for each piece of lumber. Props to opticutter.com for a great tool.

It's me! Making use of my minivan! Also visible are the other use of the minivan. Mainly lugging my kids around.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

All of the cuts needed out of the 2x3s

My favorite off cut, it's a tree! I love how the rings separated.

Some time with a shop vac and some trash bags later we have a much nicer looking situation. I want to put the shelf on the left there.

A not so messy garage. Well it's still messy but it's better!

Look a very bent 2x3 on the floor!

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

A tape measure measuring my plywood, clearly showing 80.5 inches.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

look it's 4x4s under plywood! Setup so I wont accidentally cut them.

There's a very feint pencil line down the middle of this sheet of plywood, I'm going to try to cut it.

it worked! it's mostly straight! +- .25 inches

A cut in half bit of plywood

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Carefully balancing the 4x4s on the end with the 2x3 bits placed around it. It worked!

Another view of the placement of the top frame.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

The feet of a kid riding the shelving like a surfboard.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

A finished shelving unit in a not so dirty garage!

A glamor shot from below

A nice shot of the top corner, you can see the screws and the 10"x10" squares I had to cut out of the lower shelf but never mentioned.

The underside of the top, notice the support pieces up against the 4x4s that keep it steadier probably.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

The messy garage

The half clean garage with a beautiful new shelving unit.

Francis 🏴‍☠️ Gulotta

Posted on November 17, 2024

Francis 🏴‍☠️ Gulotta

Posted on November 18, 2024

A small, green, plastic cubish end cap for a 4x4 with a square shape and sloped sides, placed on a wooden surface.

A wooden shelving unit is displayed in a garage setting. The shelving unit features a light-colored wooden top supported by four legs, with one leg having a green plastic foot. A ladder is leaning against the wall beside the shelves.

Francis 🏴‍☠️ Gulotta

Posted on November 24, 2024

A wooden shelf in a garage holds multiple air conditioning units. A ladder is leaning against the wall. It has two 3D printed feet to level out the legs from the garages slope. It’s beautiful.

Roborooter.com © 2025
Powered by ⚡️ and 🤖.